logocuoi.png

  • sk
  • sk
    HomeSẢN PHẢMFACTORY AUTOMATIONSunX - PanasonicServo motor 〉 High Speed, Multi-Point Laser Displacement Sensor HL-D3

    ONLINE SUPPORT

    MR. TUNG

    0934 36 1799

    [email protected]

    High Speed Multi-point Sensing and Stable Appearance Measurement in One Device

     

    HL-D3
    CE Marking Korean KC FDA

    CE , Korean KC , FDA Approved
    CE : EMC Directive
    FDA : HL-D301B, HL-D301C only

     

    Features

    The functionality of 500 displacement sensors in just a 12.5 mm 0.492 in wide device!

     

    Four Modes for Different Measurement Requirements

    The HL-D3 series is equipped with four sensing modes to cater to a variety of measurement needs, including in-line high-speed sensing and off-line high-precision detection.

    Multi-select displacement sensing mode [MSDS]
    The displacement sensor senses up to 10 measurement points specified on the X axis (measurement range of width) and completes the judgment at super-high speed.
    >>Click here

    Whole synchronized measurement mode
    The displacement sensor performs sensing of all target objects with the same sensitivity adjustment throughout the entire measurement range of width (X axis). This mode is suitable for the sensing of fast-moving objects.

    Multi-zone beam control measurement mode [MZBC]
    High-precision sensing is achieved by segmenting the measurement range of width (X axis) to optimize light intensity. This mode is suitable for the sensing of objects with varied glossiness or color.
    >>Click here

    Constant pitch measurement mode
    Sensing is performed at even intervals upon adjusting the sensitivity per the pitch specified along the measurement range of width (X axis). High-speed sensing is made possible by the reduced number of sensing points.

     

    HL-D3 adopts parallel beam made possible by the latest optical system. The reduced area of shadow that appears when light is emitted on the target object made it possible to accurately sense the shape of the object.

     

    Multiple Shape Calculation Functions and Two Judgment Outputs

    The HL-D3 series calculates the shapes, including the height difference, width, and cross-sectional area, from the shape waveform based on the received light. At the same time, the displacement sensor uses these calculation results to instantaneously make Hi / Go / Lo judgments based on the present upper and lower limits.
    (Only height calculation and step calculation in multi-select displacement sensing mode)
    Thanks to the two sets of output, different shape calculations can be performed for each output or two sensor heads can be connected and used to output each judgment results.

    Shape calculation is performed using the representative values extracted from the set calculation area based on the specified conditions. This technique has the benefit of tolerating any shifts in the position of objects being sensed as long as they are within the calculation area.

    Height calculation

    Height calculation
    The height difference between the reference value and measured value is calculated.

    Width calculation

    Width calculation
    The width is calculated from 2 measured values.

    Step calculation

    Step calculation
    The height difference is calculated from 2 measured values.

    Cross-sectional area calculation

    Cross-sectional area calculation
    HL-D3 calculates the cross-sectional area defined by the reference value.

     

    Settings & Monitoring Software (HL-D3SMI) Provided as Standard

    Conditions and the monitoring of measurements and judgment results can easily be set up by connecting to the HL-D3C controller and a PC pre-installed with HL-D3SMI using USB cables. The shape waveform based on the saved data can be reproduced on screen, which allows for it to be used as an analytical tool.

     

    ■ Main (Settings) screen
    The Main screen is where you set up the controller operations and the conditions for the sensor head and individual functions.

    Main (Settings) screen
     

     

    ■ Received light intensity image screen
    On this screen, you can review the light receiving status of the 2D image sensor built into the sensor head, as well as the shape waveform of the measured values.

    Received light intensity image screen
     

    ■ Operating environment

    OS Microsoft Windows® 7 Professional 32 bit / 64 bit
    Microsoft Windows® 8.1 Pro 32 bit / 64 bit
    Microsoft Windows® 10 Pro 32 bit / 64 bit
    (Japanese, English, Chinese)
    CPU 1 GHz or more
    Memory 2 GB or higher
    Screen display SXGA (1280 × 1024 full colors) or more
    Hard disc 50 MB or more of available memory
    USB interface USB 2.0 Full Speed (USB 1.1 compatible) compliant
    * A CD-ROM drive is required for installation.
    * Windows 7, 8.1 and 10 are trademarks or registered trademarks of Microsoft Corporation in the United States and other countries.

     

    HL-D3SMI (monitoring software) can. [PART 1]

    • Easily identify the sensed point based on the display of the displacement shape waveform obtained from the light intensity waveform
    • Display the calculation area along with the displacement shape waveform in order to enable an instant understanding of the calculated point and area
    • Display the calculated values of height difference, width, and cross-sectional area on the screen
    • List the displacement value of each sensing point when operating in MSDS mode
     
    Screen displaying measured values
    Screen displaying measured values
     
     
     
    Screen displaying multi-point displacement values
    Screen displaying multi-point displacement values

     

    HL-D3SMI (monitoring software) can. [PART2]

    • Store displacement shape waveform data, calculated measured values, and judgment results on the memory built into the controller during continuous sensing.
    • Provides a stereoscopic representation of the shape by a 3D display of stored data.
    • Replay the stored data on the buffering screen at a later time, provided that the stored data is saved in the dedicated file format.
    • Allow waveform display and analysis by means of spreadsheet software based on the data saved in CSV file format.
    Buffering display screen
    Buffering display screen


    What is multi-select displacement sensing? [MSDS]

    Conventional 2D displacement sensors produced the measurements of the specified points after sensing the entire measurement range of width (X axis), which made them unsuitable for high-speed sensing.
    The HL-D3 series performs efficient internal processing by sensing only the displacements at the specified points. This feature enables super-fast measurement, from sensing to calculation and judgment. Sensitivity is also adjusted at each point to ensure optimized sensing in order to also achieve high precision.
    (MSDS: Multi-Select Displacement Sensing)

    [Features]

    • High-speed sampling
      → Max. speed 80 μs (for 2-point specified)
    • Sensing points can be specified as desired
      → Up to 10 points
    • Measurements of specified points can be buffered
    • Height, step calculation, and judgment results can be output
    • Wide-cell function

    [Wide-cell function]
    When the surface condition is rough, such as with cut metal, sensing of a single point will result in errors due to the uneven surface.
    The wide-cell function expands the sensing points for the light receiving side and obtains the mean value (or maximum or minimum value, depending on the setting) to improve the stability of the measurements.

    Wide-cell function


    What is multi-zone beam control? [MZBC]

    Conventional 2D displacement sensors uniformly use the same light intensity adjustment for the entirety of the measurement range of width (X axis). When parts with significantly differing reflectance exist, the received light intensity becomes saturated or insufficient, preventing the acquisition of effective measurement results.
    The HL-D3 series breaks down the measurement range of width (X axis) into small segments and adjusts the emission for each segmented unit (called "light intensity adjustment unit") for optimal sensitivity in order to achieve stable, high-precision sensing.
    (MZBC: Multi-Zone Beam Control)

    [Features]

    • Stable sensing is possible even with objects of which reflectance is not consistent throughout the whole object
      → Both metal and resin parts exist
      → Profile consists of flat and sloped parts
    • High-precision sensing
      → Resolution of 1 μm 0.039 mil (average number of samples: 64 with average height measurement)
    • Calculation and judgment results of width, step, and cross-sectional area can be output

    HL-D3 series version upgrade

    The following five functions have been added to models produced in and after September 2013:

    ■Automatic following function for the measurement area
    ■Increased OUT calculations
    ■Mask function
    ■I/O terminal switching function
    ■Specular reflection installation supported

    THU DUC TECH Co., Ltd

    Address: : A12/2A  Le Van Viet, Tang Nhon Phu A Ward , 9 District, Ho Chi Minh City

    Phone: 0934 36 1799

    Email: [email protected]

    www.thuductech.com.vn

    0934 361 799